Что я буду изучать?

Degrees are granted in Chemical Engineering, Materials Engineering, Process Control and Welding Engineering. Welding Engineering is not available at the doctoral level. The MEng degree is intended primarily for part-time students who are working in industry, but can also be taken by full-time students.

General fields for research in chemical engineering include fluid mechanics and rheology; reaction kinetics and catalysis; mass transfer and separation processes; heat transfer; thermodynamics, hydrocarbon P-V-T and phase equilibrium studies; polymer reactor engineering; computer process control; dynamic simulation; biotechnology, mathematical modelling and environmental engineering. Many research programs are oriented toward better utilization of natural resources in the province, e.g., upgrading of Athabasca bitumen and heavy oil feedstocks; processing of natural gas.

Active research areas in materials engineering include mineral processing; coal preparation; modelling and simulation; intelligent processing of materials and solidification processing; hydrometallurgy; pyrometallurgy; high temperature electrochemistry; corrosion; physical and mechanical metallurgy; process metallurgy; welding metallurgy; powder metallurgy; ancient materials; ceramic materials; and electronic materials. Active research areas in chemical process control include dynamic modeling, state and parameter estimation, model predictive control, fault monitoring and diagnosis and process optimization.

The Department offers PhD degrees with specializations in Chemical Engineering, Process Control, and Materials Engineering.

Coursework (★20.5)

Six ★3 courses which must be approved by the Associate Chair (Graduate).

At least three courses must be 600-level or higher courses in the Department of Chemical and Materials Engineering. The following courses are considered to be equivalent to 600-level CME courses:

ECE 540
ECE 560
ECE 561
ECE 760
ECE 662
ECE 664
ECE 665
ENG M 646
MEC E 615

The remaining three courses must be at the 500-level or higher in the Faculty of Engineering, or be at the 400-level or higher in a Science department. Science courses at the 400-level must be approved by the Associate Chair (Graduate). The following courses are considered to be equivalent to 500-level Engineering courses:

ECE 450
ECE 457

Students specializing in Materials Engineering must take MAT E 640 - Advanced Materials Thermodynamics as one of their three 600-level courses
Reading courses will not count towards the total course requirements.
Students may be eligible for a Department course exemption if they have previously completed a recognized graduate degree program at an accredited university

ENGG 600 (★0.5)- Engineering Ethics and Integrity
CME 600 (★2) – Introduction to Research Methods. This course must be completed in the first year in the doctoral program.

Thesis

Registration in 900-level THES. Students are required to complete a thesis which embodies the results of independent research. All PhD students are required to deliver one public presentation on their research.

Length of Program

The maximum time to complete the PhD program as set by the Faculty of Graduate Studies and Research is six years.

На каком факультете я буду учиться?

Faculty of Engineering

Варианты обучения

Очная (6 лет)

Цена
CAD$8,700.00 (512,972 руб) за 1 год
Thesis-Based yearly fee: CAN $8,700; Course-Based yearly fee: CAN $9,321.6

*Это примерная цена, проверьте ее в вузе

Дедлайн для заявки

Предполагаемое начало: October 2022

Начало обучения

5 Январь 2022

Где

University of Alberta

North Campus,

116 Street and 85 Avenue,

EDMONTON,

Alberta (AB),

T6G 2R3, Canada

Вступительные требования

Для студентов, проживающих в Соединенных Штатах

MBA courses: students who obtain a grade of less than C+ or who fail to complete one of the MBA courses may, upon the recommendation of the Associate Dean (MBA), with the approval of the Faculty of Graduate Studies and Research, retake the course(s) or take an alternate course(s). Students repeating or taking an alternate course(s) must obtain a minimum grade of C+ and must maintain a cumulative grade point average of 2.7

Для иностранных студентов

Students applying to a PhD program directly from a BSc must have an average of at least 3.5 on a four-point scale in the last ★60 or two years of undergraduate or graduate work at the University of Alberta, or an equivalent qualification from a recognized institution.

Students with a Masters' degree in Chemical or Materials Engineering (or a related discipline) are only eligible for admission into the PhD program.

English Language Proficiency

  • a minimum TOEFL score of 92 (internet-based) with at least 20 in each section or equivalent
  • an overall band score of 7.0 on IELTS with at least 6.0 on each band
  • a minimum score of 90 on MELAB
  • a minimum overall score of 65 on the CAEL with at least 60 on each subtest
  • a minimum score of 62 on the PTE Academic.

For Fall (September) admission, the application deadlines are April 1, For Winter (January) admission, the application deadlines are October 1.

ДОБАВИТЬ В ШОРТ-ЛИСТ

O University of Alberta

University of Alberta входит в мировой топ-100 и занимает 2-е место по уровню трудоустройства выпускников среди вузов Канады.

  • Эдмонтон – это современный город, окруженный природой
  • University of Alberta входит в топ-5 университетов Канады
  • вуз состоит из 18 факультетов и 5 кампусов
  • у вуза один из самых высоких уровней трудоустройства в Канаде

Оставайтесь на связи